Claims (3)
Измельчитель работает следующим образом . Растительна масса подаетс в измельчитель сверху в направлении фигурной стрелки, захватываетс вращающимис ножами 4 и щнеком 2, в зоне противорежущих пластин измельчаетс , и под действием центробежных сил сбрасываетс в выгрузную горловину. Растительна масса, попавша в пространство между кожухом 5 и наружным диаметром шнека 2, измельчаетс дважды. Двухопорный срез протекает с помощью ножа 4, противорежущей пластины 7 и верхней торцовой кромки направл ющих ребер 9, а затем с помощью щнека эта масса перемещаетс по боковым поверхност м направл ющих ребер 9 к нижним пластинам 8 и вновь происходит Двухопорный наклонный срез с помощью ножа, но уже следующего по ходу движени массы корма пластины 8 и боковой поверхности направл ющих ребер 9. Масса, попавша во внутреннюю полость шнека 2, измельчаетс с помощью противорежущих пластин 7, концева часть которых снабжена режущим лезвием, и радиальных прорезей 3. Здесь также осуществл етс Двухопорный срез. Миновав деку, под действием центробежных сил измельченна масса сбрасываетс в выгрузную горловину кожуха. Средн длина резки растений равна половине щага t ножей. Толщина ножей 4 должна быть на 2-2,5 мм Меньше mapt ны щели, образованной пластинами 7 и 8 и торцом направл ющих ребер 9. При необходимости в кожухе можно установить последовательно две деки и увеличить степень измельчени растений еще вдвое при сохранении щага и количества ножей 4 на роторе. Формула изобретени 1.Измельчитель волокнистого материала, преимущественно кормов, содержащий транспортер, ножи и противорежущие пластины , отличающийс тем, что, с целью упрощени конструкции и повышени равномерности резки материала, транспортер выполнен в виде вращающегос вала и установленных на нем с образованием цилиндрической спирали ножей, расположенных друг от друга на рассто нии, соответствуюплем толщине противорежущих пластин . The grinder works as follows. The plant mass is fed to the chopper from above in the direction of the figured arrow, captured by the rotating knives 4 and the pickup 2, is crushed in the area of the shear plates, and under the action of centrifugal forces is discharged into the discharge neck. The vegetable mass that has entered the space between the casing 5 and the outer diameter of the screw 2 is crushed twice. The double-back cut is carried out with the help of the knife 4, the shearing plate 7 and the upper end edge of the guide ribs 9, and then with the help of a screw, this mass is moved along the side surfaces of the guide ribs 9 to the lower plates 8 and the Double-support oblique cut is again performed with a knife, but the plate 8 and the side surfaces of the guide ribs 9 which follow the mass movement of the feed mass. The mass that has entered the internal cavity of the screw 2 is crushed by means of the counter plates 7, the end part of which is provided with a cutting blade, and Other slots 3. Here is also carried out a double-base cut. Passing the deck, the centrifugal force of the ground mass is discharged into the discharge neck of the casing. The average cutting length of a plant is equal to half a knife t knives. The thickness of the knives 4 should be 2–2.5 mm. Less than the mapt of the slit formed by plates 7 and 8 and the butt of the guide ribs 9. If necessary, two decks can be installed in the casing successively and the degree of grinding of plants can be increased even twice while maintaining schaga and the number knives 4 on the rotor. Claim 1. Grinder of fibrous material, mainly fodder, containing conveyor, knives and shearing plates, characterized in that, in order to simplify the design and increase the uniformity of cutting material, the conveyor is made in the form of a rotating shaft and mounted on it to form a cylindrical helix of knives, spaced apart by the thickness of the shear plates.
2.Измельчитель по п. I, отличающийс тем, что имеет корпус с расположенной в нем декой, котора снабжена направл ющими ребрами. 2. A shredder according to claim I, characterized in that it has a housing with a deck disposed therein, which is provided with guide ribs.
3.Измельчитель по п. 1, отличающийс TeMi, что вращающийс вал снабжен дополнительными ножами. Источники информации, прин тые во внимание при экспертизе 1. Авторское свидетельство СССР № 380273, кл. А 01F 29/00, 1971.3. Shredder according to claim 1, characterized by the TeMi that the rotating shaft is provided with additional blades. Sources of information taken into account in the examination 1. USSR Author's Certificate No. 380273, cl. A 01F 29/00, 1971.
TWv/TWv /
д I, о о оd I, oh oh oh
иг.Зig.Z