Г---1G --- 1
сд елsd ate
оо ел Изобретение относитс к электротехнике иможет быть использовано дл электропитани радиоэлектронной :апй ратуры и электротехнических систем . Целью изобретени вл етс повышение КПД и качества регулировани выходного напр жени стабилизатора . На чертеже представлена функциональна схема предлагаемого устройст ва. Устройство содержит ключевой регулирующий элемент последовательного типа 1, исд-филь,тр 2, модул тор 3, выход которого соединён с входом ключевого регул тора а ,один из входов - с.выходом блока управлени по току 4 канала управлени клю чевого регул тора, входной вывод регулирующего элемента 5 непрерывного действи последовательного типа соединен с входным выводом ключевого регул тора, а выходной вывод - с одн ймейНЬ1М выходным выводом 1СД-фнльтра 2, вход схемы 6 сравнений регул тора непрерывного действи подключен к выходньп выводам вторичного источника электропитани через делитель напр жени 7, а выход схемы сравнени соединен с входом блока 4 управлени по току и через датчик 8 тока с входом регул тора 5 непрерьшного действи , входы блока 9 управлени по нап р жению соединены с входными выводами вторичного источника электропитани , а выходы - соответственно с одним из входов модул тора 3 и средней точкой делител 7 напр жени , нагруз ку 10, св занную с выходными выводами вторичного источника электропитани . Устройство работает следующим образом . В статическом режиме работы вс кие изменени выходного напр жени и тока нагрузки 10 вторичного источника электропитани отрабатываютс регулирующим транзистором 5 непрерывного действи (св занного по цепи обратной св зи через датчик 8 тока, схему 6 сравнени и делитель 7 напр жени с выходными выводами стабилизатора ) и ключевьм регулирующим элементом 1, управл емым (через широтно-импульсный модул тор 3 и блок 4 управлени по току током, протекающим через датчик 8 тока. При этом сигналы, поступающие с выходов бло-. ка 9 управлени по напр жению на входы модул тора 3 и схемы 6 сравнени , не измен ют относительной длительности импульсов управлени на выходе щиротно-импульсного модул тора 3. Среднее значение тока, протекающего через регулирующий транзистор 5. непрерьюного действи и среднее значение выходного напр жени устройства поддерживаетс на заданном уровне изменением длительности замкнутого состо ни ключевого регулирующего элемента 1. При наличии возмущающих воздействий по входу устройства блок 9 управлени по напр жению вырабатывает два сигнала.. Один сигнал поступает на второй вход модул тора 3 и измен ет длительность замкнутого, состо ни ключевого регулирующего элемента 1 так, чтобы сохранить неизменным среднее значение напр жени на входе иСД-фильтра 2, Второй сигнал поступает на схему сравнени 6 и обеспечивает управление регулирующим элементом 5 непрерывного действи таким образом, чтобы сохранить на заданном уровне среднее значение выходного напр жени стабилизатора.oo ate The invention relates to electrical engineering and can be used for electrical power supply: consumer electronics and electrical systems. The aim of the invention is to increase the efficiency and quality of regulation of the output voltage of the stabilizer. The drawing shows the functional diagram of the proposed device. The device contains a key regulating element of the sequential type 1, isd-filter, mp 2, modulator 3, the output of which is connected to the input of the key regulator a, one of the inputs is the output of the control unit with current 4 control channels of the key regulator, input the output of the continuous regulating element 5 of the series type is connected to the input terminal of the key regulator, and the output terminal is connected to the single output terminal of the 1CD-filter 2, the input of the circuit 6 of the comparisons of the continuous controller is connected to the output terminals of the second power supply through the voltage divider 7, and the output of the comparison circuit is connected to the input of the current control unit 4 and through the current sensor 8 to the input of the continuous controller 5, the inputs of the voltage control unit 9 are connected to the input terminals of the secondary power source, and the outputs, respectively, with one of the inputs of the modulator 3 and the midpoint of the voltage divider 7, the load 10, associated with the output terminals of the secondary power supply. The device works as follows. In a static mode of operation, any changes in the output voltage and load current 10 of the secondary power supply are processed by a continuous-action transistor 5 (coupled to the feedback circuit through the current sensor 8, the comparison circuit 6 and the voltage divider 7 with the output of the stabilizer) and the key regulating element 1, controlled (through the pulse-width modulator 3 and the block 4 of the current control current flowing through the current sensor 8. In this case, the signals coming from the outputs of the control block 9 The inputs to the modulator 3 and the comparison circuit 6 do not change the relative duration of the control pulses at the output of the pulse-width modulator 3. The average value of the current flowing through the regulating transistor 5. Continuous operation and the average value of the output voltage of the device are maintained at a predetermined level by changing the duration of the closed state of the key regulating element 1. In the presence of disturbing influences on the device input, the control unit 9 on the voltage generates two signals .. One signal l enters the second input of the modulator 3 and changes the duration of the closed state of the key regulating element 1 so as to keep unchanged the average value of the voltage at the input of the SD filter 2. The second signal enters the comparison circuit 6 and provides control of the regulating element 5 of continuous acting in such a way as to maintain at a given level the average value of the output voltage of the stabilizer.