| Supported Targets | ESP32-C5 | ESP32-C6 | ESP32-H2 |
|---|
This test code shows how to configure Zigbee Coordinator and use it as an HA on/off_switch.
The ESP Zigbee SDK provides more examples and tools for productization:
- One development board with ESP32-H2 SoC acting as Zigbee Coordinator (loaded with HA_on_off_switch)
- A USB cable for power supply and programming
- Choose another ESP32-H2 as Zigbee end-device (see HA_on_off_light)
Before project configuration and build, make sure to set the correct chip target using idf.py --preview set-target TARGET command.
Before flash it to the board, it is recommended to erase NVRAM if user doesn't want to keep the previous examples or other projects stored info using idf.py -p PORT erase-flash
Build the project, flash it to the board, and start the monitor tool to view the serial output by running idf.py -p PORT flash monitor.
(To exit the serial monitor, type Ctrl-].)
As you run the example, you will see the following log:
I (441) main_task: Started on CPU0
I (441) main_task: Calling app_main()
I (461) phy: phy_version: 230,2, 9aae6ea, Jan 15 2024, 11:17:12
I (461) phy: libbtbb version: 944f18e, Jan 15 2024, 11:17:25
I (471) main_task: Returned from app_main()
I (601) ESP_ZB_ON_OFF_SWITCH: ZDO signal: ZDO Config Ready (0x17), status: ESP_FAIL
I (601) ESP_ZB_ON_OFF_SWITCH: Initialize Zigbee stack
I (611) gpio: GPIO[9]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:2
I (611) ESP_ZB_ON_OFF_SWITCH: Deferred driver initialization successful
I (621) ESP_ZB_ON_OFF_SWITCH: Device started up in factory-reset mode
I (621) ESP_ZB_ON_OFF_SWITCH: Start network formation
W (781) ESP_ZB_ON_OFF_SWITCH: Network(0x13af) closed, devices joining not allowed.
I (781) ESP_ZB_ON_OFF_SWITCH: Formed network successfully (Extended PAN ID: 74:4d:bd:ff:fe:63:f7:30, PAN ID: 0x13af, Channel:13, Short Address: 0x0000)
I (1391) ESP_ZB_ON_OFF_SWITCH: Network(0x13af) is open for 180 seconds
I (1391) ESP_ZB_ON_OFF_SWITCH: Network steering started
I (9561) ESP_ZB_ON_OFF_SWITCH: ZDO signal: NWK Device Associated (0x12), status: ESP_OK
I (9561) ESP_ZB_ON_OFF_SWITCH: ZDO signal: ZDO Device Update (0x30), status: ESP_OK
I (9601) ESP_ZB_ON_OFF_SWITCH: New device commissioned or rejoined (short: 0x7c16)
I (9671) ESP_ZB_ON_OFF_SWITCH: Found light
I (9671) ESP_ZB_ON_OFF_SWITCH: Try to bind On/Off
I (9681) ESP_ZB_ON_OFF_SWITCH: Bound successfully!
I (9681) ESP_ZB_ON_OFF_SWITCH: The light originating from address(0x7c16) on endpoint(10)
I (9751) ESP_ZB_ON_OFF_SWITCH: ZDO signal: ZDO Device Authorized (0x2f), status: ESP_OK
I (9781) ESP_ZB_ON_OFF_SWITCH: Network(0x13af) is open for 180 seconds
I (16451) ESP_ZB_ON_OFF_SWITCH: Send 'on_off toggle' command
I (17011) ESP_ZB_ON_OFF_SWITCH: Send 'on_off toggle' command
I (17441) ESP_ZB_ON_OFF_SWITCH: Send 'on_off toggle' command
I (17831) ESP_ZB_ON_OFF_SWITCH: Send 'on_off toggle' command
- By toggling the switch button (BOOT) on this board, the LED on the board loaded with the
HA_on_off_lightexample will turn on and off.
For any technical queries, please open an issue on GitHub. We will get back to you soon.