Version: 1.2.2
Release Date: 2014-02-05
www.pololu.com
This is a library for the Arduino that interfaces with L3GD20H, L3GD20, and L3G4200D gyros on Pololu boards. It makes it simple to read the raw gyro data from these boards:
- L3GD20H 3-axis gyro carrier
- L3GD20 3-axis gyro carrier
- MinIMU-9 v2 (L3GD20 and LSM303DLHC carrier)
- AltIMU-10 (L3GD20, LSM303DLHC, and LSM331AP carrier)
- L3G4200D 3-axis gyro carrier (discontinued)
- MinIMU-9 (L3G4200D and LSM303DLM carrier) (discontinued)
- MinIMU-9 (L3G4200D and LSM303DLH carrier) (discontinued)
Download the archive from GitHub, decompress it, and move the “L3G” folder into the “libraries” subdirectory inside your Arduino sketchbook directory. You can view your sketchbook location by selecting File→Preferences in the Arduino environment; if there is not already a “libraries” folder in that location, you should create it yourself. After installing the library, restart the Arduino environment so it can find the L3G library and its example.
Make the following connections with wires between the Arduino and the L3G board:
Arduino L3G board
----------------------
5V -> VIN
GND -> GND
SDA -> SDA
SCL -> SCL
Arduino L3G board
----------------------
5V -> VIN
GND -> GND
2 -> SDA
3 -> SCL
Arduino L3G board
----------------------
5V -> VIN
GND -> GND
A4 -> SDA
A5 -> SCL
Open an example code sketch by selecting File→Examples→L3G→example_name
This program continuously reads the gyro, communicating the readings over the serial interface. You can display the readings with the Arduino Serial Monitor.
Example output:
G X: 188 Y: -10 Z: -47 G X: 138 Y: -40 Z: -26 G X: 110 Y: -55 Z: 4
These programs make use of the L3G library but are not included with in the library archive or repository.
- MinIMU-9 + Arduino AHRS
- This sketch allows an Arduino connected to a MinIMU-9 or AltIMU-10 to function as an attitude and heading reference system, calculating estimated roll, pitch, and yaw angles from sensor readings that can be visualized with a 3D test program on a PC. It is based on the work of Jordi Munoz, William Premerlani, Jose Julio, and Doug Weibel.
- Pololu_Open_IMU by mikeshub
- This is an alternative AHRS implementation that uses the Madgwick algorithm.
- ascii_graph by drewtm
- This sketch outputs a text-based graph of LSM303 accelerometer and L3G gyro data, providing a quick way to check whether the sensors are working as expected.
vector g- The last values read from the gyro.
bool init(byte device, byte sa0)- Initializes the library with the device being used (L3G4200D or L3GD20) and the state of the SA0 (slave address least significant bit) pin. Constants for these arguments are defined in L3G.h. Both of these arguments are optional; if they are not specified, the library will try to automatically detect the device and slave address, and it will return a boolean indicating whether the autodetection was succesful.
Note: Automatic detection of the device type currently does not work with the Arduino Due because of issues with its Wire library. To work around this, specify the device and SA0 state manually (e.g.init(L3GD20_DEVICE, L3G_SA0_HIGH)). void enableDefault(void)- Turns on the gyro in the default configuration.
void writeReg(byte reg, byte value)- Writes a gyro register with the given value. Register address constants are defined in L3G.h.
byte readReg(byte reg)- Reads a gyro register and returns the value read.
void read(void)- Takes a reading from the gyro and stores the values in the vector
g.
This library is very similar to our earlier L3G4200D library, which is not compatible with the L3GD20. Besides the name change, the main difference in this library is that you need to call the init() function before using any of the other library functions, typically from within the Arduino setup() function. While the older library only works with the Pololu boards’ default gyro slave address of 1101001b, this library allows you to specify the slave address with the init() function.
- 1.2.2 (2014-02-05): Added support for L3GD20H.
- 1.2.1 (2012-10-31): Cast sensor readings to 16-bit ints for better portability.
- 1.2.0 (2012-07-06): Renamed library to L3G and added support for L3GD20.
- 1.1.0 (2011-12-12): Arduino 1.0 compatibility.
- 1.0.0 (2011-09-14): Original release of L3G4200D library.