Clean Technologies

This research study addresses the challenges of extended charging times and limited ranges in electric vehicles by conducting a techno-economic analysis of integrating renewable energy technologies—solar modules, wind turbines, and piezoelectric materials—into double-decker electric buses in London, UK. Consequently, the empirical study evaluates the power output of renewable energy technologies through simulation modelling based on vehicle specifications and energy requirements, which is followed by numerical modelling to assess economic viability. Furthermore, CFD (computational fluid dynamics) modelling is undertaken to examine the performance levels of vehicular-mounted wind turbines. The solar modules are placed on the rooftop and sides of the bus, generating 15.9 kWh/day, and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, thereby rendering this technology impractical for further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day, resulting in savings of 19.36 min for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175, respectively. The annual revenue would be £6712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity generation, the electricity generation rate, and the initial investment are identified as key factors influencing power outages in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation toward the implementation of renewable energy technologies on electric bus fleets. Full article

Nanofine zero−valent iron (nZVI) is a new, eco−friendly material with strong reducing and adsorbent properties that can be used to clean up heavy metal−affected soils. Herein, nZVI encapsulated with carboxymethyl cellulose (CMC−nZVI) is synthesized via an aqueous−phase reduction technique and subsequently deployed to evaluate its effectiveness in Cr(VI) soil remediation. The characterization analysis used SEM−EDS, XRD, XPS, and LSV to determine the relevant properties of the material. The results show that at an initial Cr(VI) concentration of 169.5 mg·kg⁻¹, 93.2% of Cr(VI) was removed from the soil after 10 h of treatment with CMC−nZVI at pH 3.3. The kinetic analysis showed that CMC−nZVI had the maximum equilibrium adsorption capacity for removing Cr(VI) from soil at 105.3 mg·g⁻¹. This followed a pseudo−second−order kinetic model. The study shows that CMC−nZVI converts Cr(VI) to Cr(III), which forms complexes with Fe(III) ions in the presence of hydroxide ions (OH⁻) to form a highly stable compound that eventually adsorbs into the nanomaterial’s surface for efficient removal. Full article

Alternative options have been studied to mitigate the negative impact of fossil fuel sources, mainly especially when it comes to alternative energy sources. In this work, cannabis residues have been considered as a potential biomass residues for energy recovery due to their energy content, and the increase in the cannabis market in Canada has created an opportunity niche for treating and valorizing these residues as energy. This study thus aims to investigate the potential of energy recovery from cannabis residue pellets via combustion and the impact of steam explosion on the pellets’ properties as well as combustion behavior. Two batches of pellets were produced namely with and without the steam explosion pretreatment. The properties of the pellets were then compared to those of the CANplus certification. Cannabis pellets were then combusted at 290 °C in a fixed-bed reactor using three different air coefficients (α) ranging from 1 to 1.3 (α = 1.0, α = 1.15, and α = 1.3). Flue gas quantification was performed using gas chromatography combined with a NO_x detector. Results showed that the properties of this biomass is comparable to other sources of lignocellulosic biofuels. The steam explosion pretreatment enhanced pellet properties, including higher heating value (HHV), ash content, durability, and fines allowing the product to reach the CANplus requirements. The air coefficients influenced the emission levels, with an optimal value at α = 1.15, that indicated an improved combustion quality. However, steam explosion negatively affected combustion efficiency, resulting in incomplete combustion. Overall, cannabis residues show a strong potential for energy recovery and could offer a sustainable option for bioenergy applications. Full article

While the attempts to find new energy sources have intensified, the interest in the use of biomass as a carbon-rich raw material still is increasing. In this work, we studied iron-, cobalt-, and nickel-based materials in the process of CO₂-assisted gasification of sunflower husk. The materials with and without metal additives were examined by XRD, SEM, EDX, and TEM techniques and were tested in their gasification under the action of CO₂. It was found that the Co-based material demonstrates the best activity among the studied ones (the CO₂ conversion was up to 83%). The possible reason for such superiority may be related to the capability of Ni compounds to the formation of the metallic nickel phase and insufficient activity of iron species. Full article

Enhancing the eco-efficiency of municipal solid waste (MSW) services is pivotal for the shift toward a circular economy. Although the Data Envelopment Analysis (DEA) method is widely used, it is susceptible to overfitting, potentially distorting eco-efficiency assessments. This study applies the efficiency analysis tree (EAT) method, which synergizes machine learning and linear programming, offering a more reliable framework for eco-efficiency evaluation in the MSW sector. This innovative approach provides deeper insights into the optimal levels of operational costs and unsorted waste. The research encompasses a case study of 98 Chilean municipalities from 2015 to 2019, uncovering significant disparities in optimal operational expenses and unsorted waste quantities, which underscores the necessity for customized waste management approaches. The average eco-efficiency scores for 2015–2019 range between 0.561 and 0.566. This means that assessed municipalities can reduce unsorted waste by amounts ranging from 1,632,409 tons/year (2016) to 1,822,663 tons/year (2018). Potential economic savings estimated are 105,973 USD/year (2019), which represents 44% of the total MSW management costs. Additionally, the investigation into the effects of external factors on eco-efficiency furnishes nuanced perspectives that can guide policymakers and municipal authorities in developing effective, context-specific waste management strategies. Beyond refining eco-efficiency evaluations, this study contributes to more informed decision-making processes, aiding the progression toward sustainable waste management practices. Full article

This study addresses the significant environmental challenge of pharmaceutical pollutants by demonstrating the effectiveness of a hybrid electrocoagulation–adsorption (EC-A) technique for removing Montelukast Sodium (MS) from contaminated water. The research was conducted in three stages—adsorption, electrocoagulation, and adsorption using the residual water from the electrocoagulation process. The adsorbent materials were characterised using various analytical techniques: X-ray Diffraction (XRD) for determining the crystalline structure, Energy-Dispersive X-ray Spectroscopy (EDX) for elemental composition, Scanning Electron Microscopy (SEM) for surface morphology, and Fourier Transform Infrared Spectroscopy (FTIR) for identifying functional groups before and after interaction with the pollutants. The adsorption phase achieved optimal results at a pH of 3 and a contact time of 120 min, with a maximum removal efficiency of 99.5% for a starting MS concentration of 50 mg/L using Calcium Ferric Oxide–Silica Sand (CFO-SS) adsorbent. The electrocoagulation phase showed a 97% removal efficiency with a pH of 11, a current density of 20 mA, and a 5 mm electrode distance, achieved in just 20 min. Finally, the combined EC-A process, with the pH of residual water adjusted to 3, further enhanced the removal efficiency to 74%, highlighting the method’s potential for pharmaceutical contaminant removal. These findings underscore the potential of the EC-A technique as a highly effective and adaptable solution for mitigating pharmaceutical contaminants in water. Full article

This study investigates the optimization of aeration rates for the biodrying of market waste using negative-pressure ventilation. Market waste, characterized by a high moisture content (MC) and rapid decomposition, presents challenges in waste management. Over 12 days, three aeration rates (ARs) of 0.2, 0.4, and 0.6 m³/kg/day were examined, and the most effective continuous ventilation configuration was identified in terms of heat generation, moisture reduction, and biodrying efficiency. The results indicate that the most effective AR for heat retention and moisture removal was 0.2 m³/kg/day, achieving a 6.63% MC reduction and a 9.12% low heating value (LHV) increase. Gas analysis showed that, while AR 0.2 supported high microbial activity during the initial 7 days, AR 0.6 sustained higher overall CO₂ production due to its greater aeration rate. The findings also suggest that the biodrying of market waste with a high initial MC can achieve significant weight loss and leachate generation when paired with a high aeration rate of 0.6 m³/kg/day, with a 69.8% weight loss and increased waste compaction being recorded. The study suggests that variable ARs can optimize biodrying, making market waste more suitable for conversion to refuse-derived fuel or landfill pre-treatment and improving waste-to-energy processes and sustainability. Full article

The growing adoption of lithium iron phosphate (LiFePO₄) batteries in electric vehicles (EVs) and renewable energy systems has intensified the need for sustainable management at the end of their life cycle. This study introduces an innovative method for recycling lithium from spent LiFePO₄ batteries and repurposing the recovered lithium carbonate (Li₂CO₃) as a carbon dioxide (CO₂) absorber. The recycling process involves dismantling battery packs, separating active materials, and chemically treating the cathode to extract lithium ions, which produces Li₂CO₃. The efficiency of lithium recovery is influenced by factors such as leaching temperature, acid concentration, and reaction time. Once recovered, Li₂CO₃ can be utilized for CO₂ capture in hydrogen purification processes, reacting with CO₂ to form lithium bicarbonate (LiHCO₃). This reaction, which is highly effective in aqueous solutions, can be applied in industrial settings to mitigate greenhouse gas emissions. The LiHCO₃ can then be thermally decomposed to regenerate Li₂CO₃, creating a cyclic and sustainable use of the material. This dual-purpose process not only addresses the environmental impact of LiFePO₄ battery disposal but also contributes to CO₂ reduction, aligning with global climate goals. Utilizing recycled Li₂CO₃ decreases the demand for virgin lithium extraction, supporting a circular economy. Furthermore, integrating Li₂CO₃-based CO₂ capture systems into existing industrial infrastructure provides a scalable and cost-effective solution for lowering carbon footprints while securing a continuous supply of lithium for future battery production. Future research should focus on optimizing lithium recovery methods, improving the efficiency of CO₂ capture, and exploring synergies with other waste management and carbon capture technologies. This comprehensive strategy underscores the potential of lithium recycling to address both resource conservation and environmental protection challenges. Full article

Efficient and clean treatment of wastewater and energy recovery and utilization are important links to realize low-carbon development of oilfields. Therefore, this paper innovatively proposes a multi-energy complementary co-production heating system which fully and efficiently utilizes solar energy resources, oilfield waste heat resources, and biomass resources. At the same time, a typical dormitory building in the oil region was selected as the research object, the system equipment selection was calculated according to the relevant design specifications. On this basis, the simulation system model is established, and the evaluation index and operation control strategy suitable for the system are proposed. The energy utilization rate of the system and the economic, energy-saving, and environmental benefits of the system are simulated. The results show that, under the simulated conditions of two typical days and a heating season, the main heat load of the system is borne by the sewage source heat pump, the energy efficiency is relatively low in the cold period, and the energy-saving characteristics are not obvious. With the increase in heating temperature and anaerobic reactor volume, the energy consumption of the system also increases, and the energy efficiency ratio of each subsystem and the comprehensive energy efficiency ratio of the system gradually decrease. In addition, although the initial investment in cogeneration heating systems is high, the operating costs and environmental benefits are huge. Under the condition of maintaining 35 °C, the anaerobic reactor in the system can reduce carbon emissions by 12.15 t per year, reduce sulfur dioxide emissions by 98.4 kg, reduce dust emissions by 49.2 kg, and treat up to 2700 t of sewage per year, which has broad application prospects. Full article

Environmental protection and greenhouse gas (GHG) emissions are getting increasingly high priority in the area of mobility. Several regulations, goals and projects have been published in recent years that clearly encourage the reduction of carbon dioxide (CO₂) emission, the adoption of green alternatives and the use of renewable energy sources. The study compares CO₂ emissions between conventional diesel and liquefied natural gas (LNG) heavy-duty vehicles (HDVs), and furthermore investigates the main influencing factors of GHG emissions. This study was carried out in a test–track environment, which supported the perfect reproducibility of the tests with minimum external influencing factors, allowing different types of measurements. At the results level, our primary objective was to collect and evaluate consumption and emission values using statistical methods, in terms of correlations, relationships and impact assessment. In this research, we recorded CO₂ and pollutant emission values indirectly via the fleet management system (FMS) using controller area network (CAN) messages. Correlation, regression and statistical analyses were used to investigate the factors influencing fuel consumption and emissions. Our scientific work is a unique study in the field of HDVs, as the measurements were performed on the test track level, which provide accuracy for emission differences. The results of the project clearly show that gas technology can contribute to reducing GHG emissions of HDVs, and LNG provides a reliable alternative way forward for long-distance transportation, especially in areas of Europe where filling stations are already available. Full article

Glycerol, a byproduct of biodiesel, has moderate energy but high viscosity, making clean combustion challenging. Quickly evaporating fine fuel sprays mix well with air and burn cleanly and efficiently. Unlike conventional air-blast atomizers discharging a jet core/film, a newly developed swirl burst (SB) injector generates fine sprays at the injector’s immediate exit, even for high-viscosity fuels, without preheating, using a unique two-phase atomization mechanism. It thus resulted in ultra-clean combustion for glycerol/methanol (G/M) blends, with complete combustion for G/M of 50/50 ratios by heat release rate (HRR). Lower combustion efficiencies were observed for G/M 60/40 and 70/30, representing crude glycerol. Hence, this study investigates the effect of premixed methane amount from 0–3 kW, and the effect of atomizing gas to liquid mass ratio (ALR) on the dual-fuel combustion efficiency of G/M 60/40-methane in a 7-kW lab-scale swirl-stabilized gas turbine combustor to facilitate crude glycerol use. Results show that more methane and increased ALR cause varying flame lift-off height, length, and gas product temperature. Regardless, mainly lean-premixed combustion, near-zero CO and NOx emissions (≤2 ppm), and ~100% combustion efficiency are enabled for all the cases by SB atomization with the assistance of a small amount of methane. Full article

China prioritizes ensuring drinking water safety, particularly in the water-scarce northwest region. This study, utilizing water quality data from 52 village and town water sources since August 2022, assesses water quality, with a specific focus on key indicators related to organic pollution sources. This study provides a scientific foundation for enhancing water quality in these sources. Employing category factor analysis for classification and grading, principal component analysis for qualitative analysis of key evaluation indicators, and the absolute principal component linear regression equation for quantitative calculation of pollution sources, this study reveals that all 52 water sources meet quality standards. Principal component analysis categorizes pollution sources as diverse types of organic compounds in surface water. Source analysis calculations highlight decay-type organic substances as major contributors to increased water color and permanganate index, with pollution contribution rates of 54.78% and 31.31%, respectively. Fecal-type organic substances dominate the increase in dissolved total solids and total coliforms, with pollution contribution rates of 56.65% and 40.16%, respectively. Additionally, high-molecular-weight organic substances exhibit lower concentrations in the water. This article presents a systematic water quality assessment methodology, which is used for the first time to qualitatively assess the types of water sources and to quantitatively trace specific sources of organic pollution in source water in northwest China. This systematic study’s results, involving initial assessment followed by traceability, recommend the adoption of a simple contact filtration and disinfection process to enhance water quality in the region. Full article

The industrial landscape has revealed two trends: increased competitiveness and a greater demand for sustainable solutions. Materials with cork in their composition are an appealing solution, since they guarantee the desired mechanical characteristics while contributing to the prevention of environmental degradation. Given the change in external factors, there has been a substantial rise in energy costs. Thus, it is essential to optimize processes, with the aim of reducing the consumption of resources, such as electricity. This project was developed at a company that manufactures cork blocks, sheets, and rolls. Regarding blocks, a critical operation of this line is the high-frequency heating, being the bottleneck of this work center. With the critical variables previously identified, planned experiments were conducted based on DOE’s full factorial methodology. Two out of four products revealed inputs with statistical significance. With these results, a reduction in parameters was implemented in the factors and interactions that showed no statistical significance. Finally, average and amplitude control charts, based on the SPC methodology, were applied to solidify and guarantee the quality of the agglomerated blocks, with the parameter changes already introduced. The company benefited from this study by having a significant reduction in its energy consumption. Full article

To maintain the carbon dioxide concentration below the no-return threshold for climate change, we must consider the reduction in anthropic emissions coupled to carbon capture methods applied in synergy. In our recent papers, we proposed a green and reliable method for carbon mineralization using ascorbic acid aqueous solution as the reducing agent for carbon (IV) to carbon (III), thus obtaining oxalic acid exploiting green reagents. Oxalic acid is made to mineralize as calcium (as the model cation) oxalate. Oxalates are solid-state reservoirs suitable for long-term carbon storage or carbon feedstock for manufacturing applications. The carbon mineralization reaction is a double-step process (carbon reduction and oxalate precipitation), and the carbon capture efficiency is invariably represented by a double-slope curve we formerly explained as a decrease in the reducing effectiveness of ascorbic acid during reaction. In the present paper, we demonstrated that the reaction proceeds via a “pure CO₂-capture” stage in which ascorbic acid oxidizes into dehydroascorbic acid and carbon (IV) reduces to carbon (III) and a “mixed” stage in which the redox reaction competes with the degradation of ascorbic acid in producing oxalic acid. Despite the irreversibility of the reduction reaction, that was demonstrated in abiotic conditions, the analysis of costs according to the market price of the reagents endorses the application of the method. Full article

As natural gas-fired combined cycle (NGCC) power plants continue to constitute a crucial part of the global energy landscape, their carbon dioxide (CO₂) emissions pose a significant challenge to climate goals. This paper evaluates the feasibility of implementing post-combustion carbon capture, storage, and utilization (CCSU) technologies in NGCC power plants for end-of-pipe decarbonization in Uzbekistan. This study simulates and models a 450 MW NGCC power plant block, a first-generation, technically proven solvent—MEA-based CO₂ absorption plant—and CO₂ compression and pipeline transportation to nearby oil reservoirs to evaluate the technical, economic, and environmental aspects of CCSU integration. Parametric sensitivity analysis is employed to minimize energy consumption in the regeneration process. The economic analysis evaluates the levelized cost of electricity (LCOE) on the basis of capital expenses (CAPEX) and operational expenses (OPEX). The results indicate that CCSU integration can significantly reduce CO₂ emissions by more than 1.05 million tonnes annually at a 90% capture rate, although it impacts plant efficiency, which decreases from 55.8% to 46.8% because of the significant amount of low-pressure steam extraction for solvent regeneration at 3.97 GJ/tonne CO₂ and multi-stage CO₂ compression for pipeline transportation and subsequent storage. Moreover, the CO₂ capture, compression, and transportation costs are almost 61 USD per tonne, with an equivalent LCOE increase of approximately 45% from the base case. This paper concludes that while CCSU integration offers a promising path for the decarbonization of NGCC plants in Uzbekistan in the near- and mid-term, its implementation requires massive investments due to the large scale of these plants. Full article

With the aim of developing an innovative water treatment approach for developing countries in the Global South, we have applied the method of treating a cavitating water stream with a plasma discharge under real conditions. To this end, we have optimised the approach after investigating the effects that occur in the treated medium during such a treatment. Based on the obtained light absorption curves of treated model solutions of titanium oxysulphate and potassium bichromate, it was found that inside the reactor the main role in the destruction of chemical contaminants is played by hydroxide ions, while outside the reactor the main chemical interaction takes place with hydrogen peroxide. The plasma treatment unit was tested in the biological wastewater treatment plant of a health resort in the territory of the Russian Federation (Almetyevsk, Republic of Tatarstan). Water samples taken directly from the tertiary decantation tank were used as real wastewater samples instead of adding chemical reagents for disinfection. It was found that with different modes of operation of the plasma treatment plant, the concentration levels of coliform bacteria, coliphages and Escherichia coli decreased significantly and fell below the limit of permissible concentrations for wastewater discharge. At the same time, the possible effect of the plasma on persistent inorganic compounds was investigated. It was shown that the plasma discharge in the flow of the incoming liquid can almost completely destroy compounds that are difficult to remove, such as hydrogen sulphide and chlorides. In the course of the study, the optimum frequency of electrical pulses of 68 kHz was selected, which ensures the lowest consumption of electrical energy while maintaining the required efficiency. Full article

In this current research, various amino acids (lysine, betaine, and cysteine) and peptides (oxidised or reduced glutathione) were considered as potential environmentally friendly alternatives to wool bleaching. A greener methodology was also applied to dyeing. Different agro-wastes (red cabbage, peppercorns, and red and yellow onion peels) served as raw pigment materials. The process’s efficiency was characterised by the whiteness degree, colour strength, and fastness to accelerated washing and perspiration. A higher whiteness index value was observed in the cysteine-based formulations. The onion peel exhibited significant tinctorial properties due to the presence of some natural mordants. All the proposed treatments were designed with a primary focus on environmental sustainability. These treatments offer a sustainable and environmentally friendly alternative to traditional bleaching and dyeing methods for wool. They reduce costs and energy consumption while creating added value by valorising waste. Full article

Biochar is a carbon-rich product obtained by pyrolyzing biomass under oxygen-limited conditions and has a wide range of potential for environmental applications. In particular, dissolved organic matter (DOM) released from biochar has an important impact on the fate of pollutants. The study aimed to systematically assess how varying pyrolysis temperatures and biomass feedstocks influence the characteristics of biochar-derived DOM. DOM samples were comprehensively characterized utilizing UV-vis spectroscopy and excitation–emission matrix (EEM) fluorescence spectroscopy, coupled with parallel factor (PARAFAC) analysis. The study discovered that pyrolysis temperature significantly affects DOM characteristics more than feedstock type. An increase in pyrolysis temperature correlated with a notable decrease in dissolved organic carbon content, aromaticity, and fluorescence intensity, alongside a marked increase in pH and hydrophilicity. PARAFAC analysis identified three distinct DOM components: two humic-like substances (C1 and C2) and one protein-like substance (C3). The proportion of protein-like substances increased with higher pyrolysis temperatures, while the humic-like substances’ proportion declined. The compositional shifts in DOM with pyrolysis temperature may significantly influence its environmental behavior and functionality. Further research is necessary to explore the long-term environmental impact and potential applications of biochar-derived DOM. Full article

This review aims to enhance the understanding of the fundamentals, applications, and future directions in hydrogen production techniques. It highlights that the hydrogen economy depends on abundant non-dispatchable renewable energy from wind and solar to produce green hydrogen using excess electricity. The approach is not limited solely to existing methodologies but also explores the latest innovations in this dynamic field. It explores parameters that influence hydrogen production, highlighting the importance of adequately controlling the temperature and concentration of the electrolytic medium to optimize the chemical reactions involved and ensure more efficient production. Additionally, a synthesis of the means of transport and materials used for the efficient storage of hydrogen is conducted. These factors are essential for the practical feasibility and successful deployment of technologies utilizing this energy resource. Finally, the technological innovations that are shaping the future of sustainable use of this energy resource are emphasized, presenting a more efficient alternative compared to the fossil fuels currently used by society. In this context, concrete examples that illustrate the application of hydrogen in emerging technologies are highlighted, encompassing sectors such as transportation and the harnessing of renewable energy for green hydrogen production. Full article