Provide the information of the box, what soc? What network card? Which dtb file are you using in LibreElec?

thanks for the quick reply
in this site they say that the cpu is S905
https://www.savagemessiahzine.com/sec__/forum/index.php?showtopic=730321
this is what i see

T95LibreELEC:~ # cat /proc/cpuinfo
Processor       : AArch64 Processor rev 4 (aarch64)
processor       : 0
processor       : 1
processor       : 2
processor       : 3
Features        : fp asimd evtstrm crc32 wp half thumb fastmult vfp edsp neon vfpv3 tlsi vfpv4 idiva idivt
CPU implementer : 0x41
CPU architecture: 8
CPU variant     : 0x0
CPU part        : 0xd03
CPU revision    : 4

Hardware        : Amlogic
Serial          : 00000000000000000000000000000000

for the network card I could only find this information

T95LibreELEC:~ # ethtool -p eth0
Cannot identify NIC: Operation not supporterd
T95LibreELEC:~ # ethtool -i eth0
driver: st_mac100
version: March_2013
firmware-version:
expansion-rom-version:
bus-info:
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: yes
suorts-priv-flags: no
[1]+  Done(127)                  lspci

for the dtb file, I think I used the file at this link, I did it a long time ago, maybe now I wouldn't be able to anymore
https://forum.libreelec.tv/thread/1223-s905-device-trees/?pageNo=3 scroll down the page, up to 8zabi

https://m.gearbest.com/tv-box-mini-pc/pp_366029.html

This seller's introduction is s905x

Your own box, with the exact logo on the motherboard's soc.

Your NIC is on the front of the motherboard.

Don't guess what dtb you use, look at the configuration file in the LibreElec system.

The information you see in unsupported buggy firmware is only misleading.

Generally speaking, any device that can use LibreElec can try armbian

If you don't have accurate information, you can't guess which firmware to use

Thanks for your interest
I disassembled the box, but with my phone the resolution is not optimal, also on the soc there is an aluminum heatsink that does not allow reading, do you know how to remove it?
meanwhile, I am attaching this photo

Is the SOC and other models marked on the bottom of the box?

I didn't quite understand which box you are talking about
the packaging box or some label on the bottom of the box?
I have done many tests with many dtb
and before that with this image openwrt_official_s905x_k5.10.154_2022.11.16.img.gz
with the image for soc s905x the screen remains black

Which dtb file are you using in LibreElec?

if it can be useful, i remember the version i downloaded for libreelec was for s905 i still have rar files
LibreELEC-S905.arm-8.2-8.2.3.1-temp_sensor_disabled.img.gz
to update kodi from android i used this ipk
kodi-17.5.1-Krypton-armeabi-v7a.apk
the dtb file I used that the one I downloaded from this link
https://forum.libreelec.tv/thread/1223-s905-device-trees/?pageNo=3

https://github.com/ophub/amlogic-s9xxx-armbian/tree/main/build-armbian/common-files/bootfs/dtb/amlogic

These two systems use similar dtb names. Don’t you know what dtb you used in the LibreELEC system before?

If you don’t know, use 5.15 firmware to try it yourself, change the name of dtb in /boot/uEnv.txt, restart the test

i found this dtb file in the documents folder gxl_p212_1g.dtb
yes I have already done a lot of tests with various dtb files
also the one downloaded from the libreelec site
that's why I wrote here
ah I forgot libreelec starts from microSD
the tests with openwrt are done with usb
and it often happens that every time I do a test I am then forced to fix the box because it does not start, luckily I have a recovery image

meson-gxl-s905x-p212.dtb

change the name of dtb in /boot/uEnv.txt, restart the test

Download this firmware test without modification:

https://github.com/ophub/amlogic-s9xxx-openwrt/releases/download/OpenWrt_Aml_lede_11.16.0025/openwrt_lede_s905x_k5.15.78_2022.11.16.img.gz

ok, now that i think about it since i used the image for s905 i never did any tests with dtb for s905x, i will try after lunch
now I'm going to pick up the kids from school
I'll let you know later

hi last night i did some tests and finally it booted with meson-gxbb-p200.dtb file

but now I have this problem

Ok, congratulations you found the right configuration.
According to previous user feedback, the s905 box does not support writing to emmc, and can only be used on USB/TF/SD cards.

maybe you didn't notice that i have no ethernet, i have no connection and no WiFi either
what can i or should i do to get connection?

https://github.com/LibreELEC/linux_openvfd/blob/master/conf/meson-gxl-s905x-t95m.conf

From this led configuration file, you are s905x

i didn't quite understand what to do now, that file is used for libreelec, do i have to do the same for openwrt? if the box does not have access to the network, it is not useful

You can't be sure what your soc is, only test these dtbs.

The armbian system in the USB can only be started on the basis of the Android system.

If the libreelec system is installed in the current box, first backup your libreelec system, and then restore to the original Android system. so that you can test armbian

You can try to copy u-boot, restart and try

https://github.com/ophub/amlogic-s9xxx-armbian/tree/main/build-armbian/armbian-docs#1212-memory-size-recognition-error

hi ophub, yesterday i tried to fix the front panel, to no avail, the box starts with the meson-gxbb-p201.dtb file
and with this the ethernet cable also works, but not the wifi
no card is detected
the leds must also be started from http://192.168.178.101/cgi-bin/luci//admin/system/leds?
for the front panel i tried some files
here https://github.com/LibreELEC/linux_openvfd/blob/master/conf/meson-gxl-s905x-t95m.conf
I uploaded them and renamed them to diy.conf
in some I have also made changes as described in this guide
https://github.com/ophub/amlogic-s9xxx-armbian/blob/main/build-armbian/armbian-docs/led_screen_display_control.md
nothing I could not turn on the panel
where am i wrong?

meson-gxbb-p201.dtb

Wired internet works just fine. Because it does not add wireless and led related codes in its dtb, so other tests are invalid.
What is your wireless chip?

I have no idea what it could be, if I start libreelec can I know ?, give me time

The wireless chip is on your motherboard, look carefully at the code on the chip

here I am, sorry for the delay but we have a different time zone :)
looks like realtek 8189ETV

https://github.com/unifreq/linux-5.15.y/tree/main/drivers/net/wireless/realtek

There is no driver for 8189ETV in the kernel.

0dbf7b8
I added your device to the configuration list, and other users can use your test results in the future.

Do you use the 5.10 kernel? Take a look at which u-boot you are using. Use the following command to send a screenshot

cd /boot
cat uEnv.txt
sha256sum u-boot*

good morning ophub
here is the screen

Temperature error.

Do you use the 5.10 kernel? Use the following command to send a screenshot.

cd /boot
sha256sum u-boot*

Temperature error. These 3 lines of commands are copied and executed separately. and send a screenshot.

sensors | grep -Eo '\+[0-9]+.+C' | sed ':a;N;$!ba;s/\n/ /g;s/+//g'

awk '{ printf("%.1f °C", $0 / 1000) }' /sys/class/hwmon/hwmon0/temp1_input

awk '{ printf("%.1f °C", $0 / 1000) }' /sys/class/thermal/thermal_zone0/temp

i am using kernel 5.15

At this temperature, steel can be made and electricity can also be generated. I think the display needs to be corrected. I'll update the script in a while.

A questa temperatura si può produrre acciaio e generare elettricità. Penso che il display debba essere corretto. Aggiornerò lo script tra un po'.

I think the problem is where the "."
actually it would be 42.94

for WiFi there is no solution apparently
could this dts file be useful for wifi and lcd panel?

# Download the latest script
wget https://raw.githubusercontent.com/ophub/amlogic-s9xxx-openwrt/main/amlogic-s9xxx/common-files/patches/cpustat/30-sysinfo.sh -O /etc/profile.d/30-sysinfo.sh

You download the latest script in ttyd, then log in again to see the temperature display, and post the screenshot.

This is the driver of the Android system. Armbian uses the mainline kernel, so the driver cannot be used universally.

ok

Okay, perfect, the debugging of this box is over for the time being, please feel free to report back if you have any questions in the future.

I would need some tutorials on how to install the containers docker, I tried but I can install the containers, it starts but I don't see the web page

https://github.com/ophub/amlogic-s9xxx-armbian/blob/main/build-armbian/armbian-docs/armbian_software.md

install the docker
run: armbian-software
select: 101