Flip chip

1. Integrated circuits are created on the wafer.
2. Pads are metallized on the surface of the chips.
3. A solder ball is deposited on each of the pads, in a process called wafer bumping
4. Chips are cut.
5. Chips are flipped and positioned so that the solder balls are facing the connectors on the external circuitry.
6. Solder balls are then remelted (typically using hot air reflow).
7. Mounted chip is "underfilled" using a (capillary, shown here) electrically-insulating adhesive.^[4][5]

 

In typical semiconductor fabrication systems, chips are built up in large numbers on a single large wafer of semiconductor material, typically silicon. The individual chips are patterned with small pads of metal near their edges that serve as the connections to an eventual mechanical carrier. The chips are then cut out of the wafer and attached to their carriers, typically via wire bonding such as thermosonic bonding. These wires eventually lead to pins on the outside of the carriers, which are attached to the rest of the circuitry making up the electronic system.

 

Processing a flip chip is similar to conventional IC fabrication, with a few additional steps.^[6] Near the end of the manufacturing process, the attachment pads are metalized to make them more receptive to solder. This typically consists of several treatments. A small dot of solder is then deposited on each metalized pad. The chips are then cut out of the wafer as normal.

To attach the flip chip into a circuit, the chip is inverted to bring the solder dots down onto connectors or pads on the underlying electronics or circuit board or substrate. The solder is then re-melted to produce an electrical connection, typically using a thermosonic bonding or alternatively reflow solder process.^[7]

This also leaves a small space between the chip's circuitry and the underlying mounting. In many cases an electrically-insulating adhesive is then "underfilled" to provide a stronger mechanical connection, provide a heat bridge, and to ensure the solder joints are not stressed due to differential heating of the chip and the rest of the system. The underfill distributes the thermal expansion mismatch between the chip and the board, preventing stress concentration in the solder joints which would lead to premature failure.^[8]

Solder balls can be mounted on the chips by separately making the balls and then attaching them to the chips by using a vacuum pick up device to pick up the balls and then placing them into a chip with flux applied on contact pads for the balls, or by electroplating in which seed metals are first deposited onto a wafer with the chips to be bumped. This allows the solder to adhere to the contact pads of the chips during the electroplating process. The seed metals are alloys and are deposited by sputtering onto the wafer with the chips to be bumped. A photoresist mask is used to only deposit the seed metal on top of the contact pads of the chips. The wafer then undergoes electroplating, and the photoresist layer is removed or stripped. Then the solder on the chips undergoes solder reflow to form the bumps into their final shape. This entire process is known as wafer bumping. Solder balls are often 75 to 500 microns in diameter.^[9][10]

In 2008, High-speed mounting methods evolved through a cooperation between Reel Service Ltd. and Siemens AG in the development of a high speed mounting tape known as 'MicroTape'[1]. By adding a tape-and-reel process into the assembly methodology, placement at high speed is possible, achieving a 99.90% pick rate and a placement rate of 21,000 cph (components per hour), using standard PCB assembly equipment.

Flip chip packages often consist of a silicon die sitting on top of a "substrate" which then sits on top of a traditional PCB. The substrate can have a Ball Grid Array (BGA) on its underside. The substrate makes the connections to the die available for use by the PCB.^[11] Substates made with build up film such as Ajinomoto Build up Film (ABF), are manufactured around a core, and the film is stacked on the core in layers by vacuum lamination at high temperatures. After each layer is applied, the film is cured, and laser vias are made with CO2 or UV lasers, then the blind vias in the substrate are cleaned and the build up film is roughened chemically with a permanganate, and then copper is deposited using electroless copper plating, followed by creating a pattern on the copper using photolithography and etching, and then this process is repeated for every layer of the substrate.^[12][13]

Tape-automated bonding (TAB) was developed for connecting dies with thermocompression or thermosonic bonding to a flexible substrate including from one to three conductive layers. Also with TAB it is possible to connect die pins all at the same time as with the soldering based flip chip mounting. Originally TAB could produce finer pitch interconnections compared to flip chip, but with the development of the flip chip this advantage has diminished and has kept TAB to be a specialized interconnection technique of display drivers or similar requiring specific TAB compliant roll-to-roll (R2R, reel-to-reel) like assembly system.

The resulting completed flip chip assembly is much smaller than a traditional carrier-based system; the chip sits directly on the circuit board, and is much smaller than the carrier both in area and height. The short wires greatly reduce inductance, allowing higher-speed signals, and also conduct heat better.

Flip chips have several disadvantages.

The lack of a carrier means they are not suitable for easy replacement, or unaided manual installation. They also require very flat mounting surfaces, which is not always easy to arrange, or sometimes difficult to maintain as the boards heat and cool. This limits the maximum device size.

Also, the short connections are very stiff, so the thermal expansion of the chip must be matched to the supporting board or the connections can crack.^[14] The underfill material acts as an intermediate between the difference in CTE of the chip and board.

The process was originally introduced commercially by IBM in the 1960s for individual transistors and diodes packaged for use in their mainframe systems.^[15]

Ceramic subtrates for flip chip BGA were replaced with organic substrates to reduce costs and use existing PCB manufacturing techniques to produce more packages at a time by using larger PCB panels during manufacturing.^[16] Ajinomoto Build up Film (ABF) was developed in 1999 and has become a material widely used in flip chip packages, used for manufacturing flip chip substrates in a semi-additive process, first pioneered by Intel.^[17][18][19] Build up film helped transition the industry away from ceramic substrates, and this film is now essential in the production of organic flip chip package substrates.^[20][21]

Since the flip chip's introduction a number of alternatives to the solder bumps have been introduced, including gold balls or molded studs, electrically conductive polymer and the "plated bump" process that removes an insulating plating by chemical means. Flip chips have recently gained popularity among manufacturers of cell phones and other small electronics where the size savings are valuable.^{[citation needed]}

• Flip-Chip modules – Digital Equipment Corporation trademarked version
• Solid Logic Technology
• IBM 3081
• Hybrid pixel detector

• Amkor Flip Chip Technology: CSP (fcCSP), BGA (FCBGA), FlipStack® CSP
• Shirriff, Ken (March 2021). "Strange chip: Teardown of a vintage IBM token ring controller".