Bayonet mount

To couple the two parts, the pin(s) on the male are aligned with the slot(s) on the female and the two pushed together. Once the pins reach the bottom of the slot, one or both parts are rotated so that the pin slides along the horizontal arm of the L until it reaches the "serif". The spring then pushes the male connector up into the "serif" to keep the pin locked into place. A practised user can connect them quickly and, unlike screw connectors, they are not subject to cross-threading. To disconnect, the two parts are pushed together to move the pin out of the "serif" while twisting in the opposite direction than for connecting, and then pulling apart.

The strength of the joint comes from the strength of the pins and the L slots, and the spring. To disengage unintentionally, the pins must break, the sleeve into which the connector slides must be distorted or torn enough to free the pins, or the spring must fail and allow the connector to be pushed down and rotate—for example due to vibration.

It is possible to push down the connector and rotate it, but not far enough to engage and lock; it will stay in place temporarily, but accidental disconnection is very likely.

Bayonet electrical connectors are used in the same applications where other connectors are used, to transmit either power or signals. Bayonet connections can be made faster than screw connections, and more securely than push-fit connections; they are more resistant to vibration than both these types. They may be used to connect two cables, or to connect a cable to a connector on the panel of a piece of equipment.

The coupling system is usually made of two bayonet ramps machined on the external side of the receptacle connector and 2 stainless steel studs mounted inside the plug connector’s coupling nut. Several classes of electrical cable connectors, including audio, video, and data cables use bayonet connectors. Examples include BNC, C, and ST connectors. (The BNC connector is not exactly as described in this article, as the male, not female, connector has the slots and spring.)

The GU-10 light fittings in common use for both halogen and LED miniature spotlight lamps have a similar means of connection but the retaining pins are fitted to the end of the lamp and also double as the electrical contacts. The pins are cylindrical but the ends have a larger diameter, resembling a T when viewed from the side. The receptacle has two slots resembling curved keyholes which have holes at one end sized to accept the pin ends. The lamp is inserted into the receptacle by placing the pins in the holes and rotating in a clockwise direction. Note that, unlike the traditional bayonet fitting, the retaining springs act laterally on the pins so no inward pressure is required to lock the lamp in the fitting. GU-10 fittings are available in heat-resistant form for use with halogen lamps which generate heat.

The first documented use of this type of fitting (without the name "bayonet") may be by al-Jazari in the 13th century, who used it to mount candles into his candle-clocks.^[2] This type of fitting was later used for soldiers who needed to quickly mount bayonets to the ends of their rifles, hence the name.

 

 

 

 

 

The bayonet light bulb mount is the standard fitting in many former members of the British Empire^{[citation needed]} including the United Kingdom, Australia, India, Ireland, and New Zealand, Hong Kong, as well as parts of the Middle East and Africa (although not Canada, which primarily uses Edison screw sockets along with the United States and Mexico). The standard size is B22d-2, often referred to in the context of lighting as simply BC or B22. Older installations in some other countries, including France and Greece use this base. First developed by St. George Lane Fox-Pitt in the UK and improved upon by the Brush Electric Company from the late 1870s onward, standard bulbs have two pins on opposite sides of the cap;^[3][4] however, some specialized bulbs have three pins (cap designation B22d-3) to prevent use in domestic light fittings. Examples of three-pin bulbs are found in mercury street lamps and fireglow bulbs in some older models of electric radiative heater. Older railway carriages in the UK also made use of a 3 pin bulb base to discourage theft. Bayonet cap bulbs are also very common worldwide in applications where vibration may loosen screw-mount bulbs, such as automotive lighting and other small indicators, and in many flashlights. In many other countries the Edison screw (E) base is used for lighting.

Some bulbs may have slightly offset lugs to ensure they can be only inserted in one orientation, for example the 1157 automobile tail-light which has two different filaments to act as both a tail light and a brake light. In this bulb each filament has a different brightness and is connected to a separate contact on the bottom of the base; the two contacts are symmetrically positioned about the axis of the base, but the pins are offset so that the bulb can only be fitted in the correct orientation. Newer bulbs use a wedge base which can be inserted either way without complication. Some special-purpose bulbs, such as infra-red, have 3 pins 120 degrees apart to prevent them being used in any but the intended socket.

Bayonet bases or caps are often abbreviated to BA, often with a number after. The number refers to the diameter of the base (e.g., BA22 is a 22 mm diameter bayonet cap lamp). BA15, a 15 mm base, can also be referred to as SBC standing for small bayonet cap. The lower-case letter s or d specifies whether the bulb has single or double contacts. The entries from the table below pertain to IEC 60061 "Lamp caps and holders together with gauges for the control of interchangeability and safety"^[5] and to DIN 49xxx.^[a]

These are the available sizes in the UK:^[7]

Of these, only the BC (BA22d, often abbreviated as B22) is widely used in homes. Formerly, some linear fluorescent lamps in the UK used BA22d end caps, owing to material shortages arising from the Second World War, which prevented the development of the bi-pin cap design that was becoming commonplace elsewhere in the world; notably, in the United States. Production of these lamps continued until the early 1980s, although manufacturers had produced adaptors that permitted bi-pin lamps being used in older luminaires (equipped with bayonet lamp holders) since the 1960s. The BA20d (sometimes called a Bosch fitting) was once a common automotive (twin filament) headlamp fitting but has largely been superseded by more modern, higher-rated H-series sockets and is only used for some lower-powered applications such as combined automotive tail and stop lamps.

In Japan, the JIS C 8310 “hook ceiling” bayonet mount is quite common. It is designed to both provide power and carry the weight of a lamp. A similar concept existed in BS 7001 as the slide-in “luminaire-supporting coupler” (LSC), but its prominence is unknown.

Many cameras with interchangeable lenses use a bayonet lens mount to allow lenses to be changed rapidly and locked accurately in position. Camera lens mounts usually employ stronger flattened tabs rather than pins, though their function is the same.

A bayonet mount is often used to mate a cylinder with a base in cylindrical packaging such as that for CD spindles.

• Bi-pin lamp base
• Storz
• Arri bayonet
• Joseph Swan
• BNC connector
• Edison screw

• IEC 61184: Bayonet lampholders, International Electrotechnical Commission, 1997. (also: BS EN 61184). Specifies requirements and tests for the B15 and B22 bayonet holders for light bulbs used in some Commonwealth countries

 

Wikimedia Commons has media related to Bayonet joints.

• Line-voltage Socket Design Competition (GU24)